Need Support? Let’s guide you to the right answer or agent.

OpenCivil Ideas Portal

ADD A NEW IDEA

Annotation

Showing 176 of 1386

Auto-annotate parametric constraints, template transitions, point controls, superelevation

On road construction plans we need to label/annotate change points. We need to label where changes (lane width, superelevation transitions, side slope transitions, component start and end points, etc. ) from the “default” condition happen. The sof...
about 2 years ago in Annotation / Modeling / OpenRail Designer / OpenRoads Designer 1 Future consideration

Tabular profile annotation to include speed table values

As a light rail design engineer I want to produce profiles with a lot of information to be able to check a maximum amount of information on a single document.On critical information for light rail design is the maximum speed. This is because light...
about 2 years ago in Annotation / OpenRail Designer / OpenRoads Designer 1 Future consideration

"Curve Set" text favorite annotation should annotate entire curve set

Under the Curve Set option under Location, an option for Spiral Left Middle, Spiral Right Middle, Curve Left Middle, Curve Right Middle needs to be added. Ability to annotate the Middle of a Spiral and/or Curve within a Curve Set. These options ne...
about 2 years ago in Annotation / OpenRail Designer / OpenRoads Designer / OpenSite Designer 1 Future consideration

Add a save button to the Manage Annotations dialog. DO NOT automatically save.

The manage annotations dialog that is used to create Annotation Definitions automatically saves any changes made. If the dialog is closed then all of the changes are saved even if there was not an intent to save them. Please add a save button or a...
about 2 years ago in Annotation / OpenRail Designer / OpenRoads Designer 0 Future consideration

Civil Labeler - Along Reference Line

Currently, we can label an element at a specified interval along that element. However, we like to label elements at a specified interval not along that specific element, but rather at an interval along the alignment. Could we add the option to la...
over 1 year ago in Annotation / OpenRail Designer / OpenRoads Designer 1 Future consideration

Allow Plan Annotation>Arc>“Arc Length” property to annotate length for both Arc and Chord Definition curves so that only one text favorite is necessary to annotate curve length if both types of definitions exist in the same alignment.

With this issue we need to be able to create a single Alignment Feature Definition that will be able to annotate both Arc and Chord defined Curves in the same alignment. That single Alignment Feature Definition will have a Length Label “L” and it ...
over 1 year ago in Annotation / OpenRail Designer / OpenRoads Designer 0 Planned

Ability to customize Slopes between points symbology and ruled

When labeling site pavements slopes, the tool only allows for a pre-defined symbology (slope=X.XX% ->) and it`s a simple text.We use a different symbology, basically a arrow cell and a text between the two points.The abillity to customize the l...
over 1 year ago in Annotation / Drawing Production / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Plan Annotation by station range

It would be useful to have the ability to annotate only part of the horizontal alignment. There are situations where we need to have several different annotation groups along the alignment.
almost 2 years ago in Annotation / OpenRail Designer / OpenRoads Designer / OpenSite Designer 1 Future consideration

Label all the points in a superelevation section with Civil Labeler

Superelevation is a tabular note that goes on the general info sheet with the super elevation diagram, so we usually just fill out the info in that tabular note. Designers just blow up the tabular note to add lines and make it work per project. If...
over 1 year ago in Annotation / OpenRail Designer / OpenRoads Designer / Superelevation 0 Future consideration

Add Trailing Zeros Setting to Point Station

Need the ability to hide ".00" decimal for stationing using the trailing zeros setting. For example, station 100+00.00 would label 100+00. This is available for point offset and I've attached a screenshot of the settings needed.
3 months ago in Annotation / OpenRoads Designer / OpenSite Designer 3 Future consideration