Need Support? Let’s guide you to the right answer or agent.

OpenCivil Ideas Portal

ADD A NEW IDEA

My ideas: OpenSite Designer

Showing 696 of 1172

Disable Point Controls Rather than Delete When Control Can't Be Found

Currently when the control - profile, alignment, feature - can't be found due to a deletion or reference detachment, the corresponding point control(s) is removed from the corridor. Considering that these events may occur inadvertently and not dis...
over 1 year ago in Modeling / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

3D cut-in profile to carry the same line symbology present in the XS named boundaries

User expecting to be 3D cut should mimic the display style of the 3D view. Currently, the limitation is that a cross-section in ORD can only be cut between two lines, and not along a complex element. It should go inside the display style and let y...
over 1 year ago in Drawing Production / Modeling / OpenRail Designer / OpenRoads Designer / OpenSite Designer 1 Future consideration

Display transparent catchment boundary at the cursor when relocating an inlet.

Enable the user when relocating a catch basin to view the catchment boundary as the inlet location is adjusted. Thus, acting as a dynamic and transparent view of the catchment boundary for the inlet at the new location. This will simplify the work...
about 1 year ago in Drainage and Utilities / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Split Cross Sections if Elements in Model Extend Outside of Default Width.

Currently our DOT requires that if ROW lines (or any element in the corridor) are outside the width of the default XS width, the user needs to create an extension or split the XS's to be able to show all design elements and ROW labels. Currently t...
about 1 year ago in Drawing Production / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Make the Point Analyze Tool usable in Read-Only files

You can't use the Analyze Point tool on read-only files presumably because it is trying to add annotation but sometimes people just want to check measurements such as slope between geometry in a read-only files and this is a very useful tool to do...
about 1 year ago in Modeling / OpenRail Designer / OpenRoads Designer / OpenSite Designer 3 Future consideration

Improve "Create Terrain from Design Meshes" & "Graphical Filter" tool. Filter by Fence / Shape / Reference Clip / Level Display / Selection Set

When I first saw this tool I was so excited. I could drape the design meshes from top or bottom and create a terrain . Then I started using it and realize the tool may need some improvement because it processes everything in the file or reference ...
over 1 year ago in OpenRail Designer / OpenRoads Designer / OpenSite Designer / Terrain 2 Future consideration

Allow the road slope to exceed the gutter cross slope

My state agency commonly uses gutters with a 4% cross slope. The maximum superelevation rate is 7%. The gutter slope stays at 4% in this situation. Spread does not compute in this scenario because "A depressed gutter must have a Gutter Cross Slope...
8 months ago in Drainage and Utilities / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Enhancement to Create Project Node to Element Tool

There is currently not a way to project a node from the Drainage and Utility Model to an element (horizontal alignment’s profile model). Profile runs can be created and then projected onto the profile model by conduit linkage. With this enhancemen...
about 1 year ago in Drainage and Utilities / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Auto-rotate Annotation and Labels

Suggestion to allow annotation and labels to align with plan named boundaries and sheet file plan views. For example, consider a plan named boundaries shape around a horizontal curve. If you have a separate standalone annotation file, often times,...
over 1 year ago in Annotation / OpenBridge Designer / OpenBridge Modeler / OpenRail Designer / OpenRoads Designer / OpenSite Designer 2 Future consideration

Ability to append, join, or combine individual alignments and have it hold the sub alignment stationing, which would create station equations

In Geopak, we had the ability to take individual alignments and create an overall alignment from a subset of alignments and it would hold the individual stationing for each alignment, creating station equations. There is no way to do this in ORD u...
8 months ago in Geometry / OpenRail Designer / OpenRoads Designer / OpenSite Designer 3 Future consideration