Need Support? Let’s guide you to the right answer or agent.

OpenCivil Ideas Portal

ADD A NEW IDEA

OpenRail Designer

Showing 878 of 1172

Disable Point Controls Rather than Delete When Control Can't Be Found

Currently when the control - profile, alignment, feature - can't be found due to a deletion or reference detachment, the corresponding point control(s) is removed from the corridor. Considering that these events may occur inadvertently and not dis...
over 1 year ago in Modeling / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

3D cut-in profile to carry the same line symbology present in the XS named boundaries

User expecting to be 3D cut should mimic the display style of the 3D view. Currently, the limitation is that a cross-section in ORD can only be cut between two lines, and not along a complex element. It should go inside the display style and let y...
over 1 year ago in Drawing Production / Modeling / OpenRail Designer / OpenRoads Designer / OpenSite Designer 1 Future consideration

Display transparent catchment boundary at the cursor when relocating an inlet.

Enable the user when relocating a catch basin to view the catchment boundary as the inlet location is adjusted. Thus, acting as a dynamic and transparent view of the catchment boundary for the inlet at the new location. This will simplify the work...
about 1 year ago in Drainage and Utilities / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Split Cross Sections if Elements in Model Extend Outside of Default Width.

Currently our DOT requires that if ROW lines (or any element in the corridor) are outside the width of the default XS width, the user needs to create an extension or split the XS's to be able to show all design elements and ROW labels. Currently t...
about 1 year ago in Drawing Production / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Make the Point Analyze Tool usable in Read-Only files

You can't use the Analyze Point tool on read-only files presumably because it is trying to add annotation but sometimes people just want to check measurements such as slope between geometry in a read-only files and this is a very useful tool to do...
about 1 year ago in Modeling / OpenRail Designer / OpenRoads Designer / OpenSite Designer 3 Future consideration

Improve "Create Terrain from Design Meshes" & "Graphical Filter" tool. Filter by Fence / Shape / Reference Clip / Level Display / Selection Set

When I first saw this tool I was so excited. I could drape the design meshes from top or bottom and create a terrain . Then I started using it and realize the tool may need some improvement because it processes everything in the file or reference ...
over 1 year ago in OpenRail Designer / OpenRoads Designer / OpenSite Designer / Terrain 2 Future consideration

Allow the road slope to exceed the gutter cross slope

My state agency commonly uses gutters with a 4% cross slope. The maximum superelevation rate is 7%. The gutter slope stays at 4% in this situation. Spread does not compute in this scenario because "A depressed gutter must have a Gutter Cross Slope...
8 months ago in Drainage and Utilities / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Enhancement to Create Project Node to Element Tool

There is currently not a way to project a node from the Drainage and Utility Model to an element (horizontal alignment’s profile model). Profile runs can be created and then projected onto the profile model by conduit linkage. With this enhancemen...
about 1 year ago in Drainage and Utilities / OpenRail Designer / OpenRoads Designer / OpenSite Designer 0 Future consideration

Dynamic cross section simultaneous tracking

Please allow us to move our cursor in a dynamic cross section and allow us to see a pointer move side to side in the 2D model at the same time.
over 1 year ago in OpenRail Designer / OpenRoads Designer / User Interface 2 Future consideration

Add an Interval button to the Dynamic Cross Sections

Please add an interval setting to dynamic cross sections . This will allow users to control the interval in which to view cross sections. By default the interval matches the corridor density.
over 1 year ago in Modeling / OpenRail Designer / OpenRoads Designer 2 Future consideration